IEC61970::Base::Wires::PetersenCoil Class Reference

#include <PetersenCoil.h>

Inheritance diagram for IEC61970::Base::Wires::PetersenCoil:

Collaboration diagram for IEC61970::Base::Wires::PetersenCoil:

Public Attributes
IEC61970::Base::Wires::PetersenCoilModeKind	mode = IEC61970::Base::Wires::PetersenCoilModeKind::_undef
IEC61970::Base::Domain::Voltage	nominalU
IEC61970::Base::Domain::CurrentFlow	offsetCurrent
IEC61970::Base::Domain::CurrentFlow	positionCurrent
IEC61970::Base::Domain::Reactance	xGroundMax
IEC61970::Base::Domain::Reactance	xGroundMin
IEC61970::Base::Domain::Reactance	xGroundNominal
Public Attributes inherited from IEC61970::Base::Wires::EarthFaultCompensator
IEC61970::Base::Domain::Resistance	r
Public Attributes inherited from IEC61970::Base::Core::Equipment
IEC61970::Base::Domain::Boolean	aggregate
IEC61970::Base::Domain::Boolean	normallyInService
Public Attributes inherited from IEC61970::Base::Core::PowerSystemResource
std::list< IEC61970::Base::Meas::Control * >	Controls
std::list< IEC61970::Base::Meas::Measurement * >	Measurements
IEC61970::Base::Core::PSRType *	PSRType
Public Attributes inherited from IEC61970::Base::Core::IdentifiedObject
IEC61970::Base::Domain::String	aliasName
IEC61970::Base::Domain::String	description
IEC61970::Base::Domain::String	mRID
IEC61970::Base::Domain::String	name
std::list< IEC61970::Base::DiagramLayout::DiagramObject * >	DiagramObjects

Detailed Description

A tunable impedance device normally used to offset line charging during single line faults in an ungrounded section of network.

Member Data Documentation

mode

IEC61970::Base::Wires::PetersenCoilModeKind IEC61970::Base::Wires::PetersenCoil::mode = IEC61970::Base::Wires::PetersenCoilModeKind::_undef

The mode of operation of the Petersen coil.

nominalU

IEC61970::Base::Domain::Voltage IEC61970::Base::Wires::PetersenCoil::nominalU

The nominal voltage for which the coil is designed.

offsetCurrent

IEC61970::Base::Domain::CurrentFlow IEC61970::Base::Wires::PetersenCoil::offsetCurrent

The offset current that the Petersen coil controller is operating from the resonant point. This is normally a fixed amount for which the controller is configured and could be positive or negative. Typically 0 to 60 Amperes depending on voltage and resonance conditions.

positionCurrent

IEC61970::Base::Domain::CurrentFlow IEC61970::Base::Wires::PetersenCoil::positionCurrent

The control current used to control the Petersen coil also known as the position current. Typically in the range of 20-200mA.

xGroundMax

IEC61970::Base::Domain::Reactance IEC61970::Base::Wires::PetersenCoil::xGroundMax

The maximum reactance.

xGroundMin

IEC61970::Base::Domain::Reactance IEC61970::Base::Wires::PetersenCoil::xGroundMin

The minimum reactance.

xGroundNominal

IEC61970::Base::Domain::Reactance IEC61970::Base::Wires::PetersenCoil::xGroundNominal

The nominal reactance. This is the operating point (normally over compensation) that is defined based on the resonance point in the healthy network condition. The impedance is calculated based on nominal voltage divided by position current.

---

The documentation for this class was generated from the following files:

• /home/lukas/acs/gits/CIM_SINERGIEN/20170705/refactored/IEC61970/Base/Wires/PetersenCoil.h
• /home/lukas/acs/gits/CIM_SINERGIEN/20170705/refactored/IEC61970/Base/Wires/PetersenCoil.cpp